This document describes the changes in Ganeti 2.3+ compared to Ganeti 2.3 storage model. It also documents the ExtStorage Interface.
Contents
The aim is to introduce support for externally mirrored, shared storage. This includes two distinct disk templates:
DRBD is currently the only shared storage backend supported by Ganeti. DRBD offers the advantages of high availability while running on commodity hardware at the cost of high network I/O for block-level synchronization between hosts. DRBD’s master-slave model has greatly influenced Ganeti’s design, primarily by introducing the concept of primary and secondary nodes and thus defining an instance’s “mobility domain”.
Although DRBD has many advantages, many sites choose to use networked storage appliances for Virtual Machine hosting, such as SAN and/or NAS, which provide shared storage without the administrative overhead of DRBD nor the limitation of a 1:1 master-slave setup. Furthermore, new distributed filesystems such as Ceph are becoming viable alternatives to expensive storage appliances. Support for both modes of operation, i.e. shared block storage and shared file storage backend would make Ganeti a robust choice for high-availability virtualization clusters.
Throughout this document, the term “externally mirrored storage” will refer to both modes of shared storage, suggesting that Ganeti does not need to take care about the mirroring process from one host to another.
We consider the following use cases:
The design addresses the following procedures:
Additionally, mid- to long-term goals include:
Currently, all storage-related decision-making depends on a number of frozensets in lib/constants.py, typically constants.DTS_NET_MIRROR. However, constants.DTS_NET_MIRROR is used to signify two different attributes:
We propose the introduction of two new frozensets to ease decision-making:
Additionally, DTS_NET_MIRROR will be renamed to DTS_INT_MIRROR to reflect the status of the storage as internally mirrored by Ganeti.
Thus, checks could be grouped into the following categories:
The primary-secondary node concept has primarily evolved through the use of DRBD. In a globally shared storage framework without need for external sync (e.g. SAN, NAS, etc.), such a notion does not apply for the following reasons:
The proposed solution is using the iallocator framework for run-time decision making during migration and failover, for nodes with disk templates in constants.DTS_EXT_MIRROR. Modifications to gnt-instance and gnt-node will be required to accept target node and/or iallocator specification for these operations. Modifications of the iallocator protocol will be required to address at least the following needs:
Basic shared file storage support can be implemented by creating a new disk template based on the existing FileStorage class, with only minor modifications in lib/bdev.py. The shared file disk template relies on a shared filesystem (e.g. NFS, AFS, Ceph, OCFS2 over SAN or DRBD) being mounted on all nodes under the same path, where instance images will be saved.
A new cluster initialization option is added to specify the mountpoint of the shared filesystem.
The remainder of this document deals with shared block storage.
Basic shared block device support will be implemented with an additional disk template. This disk template will not feature any kind of storage control (provisioning, removal, resizing, etc.), but will instead rely on the adoption of already-existing block devices (e.g. SAN LUNs, NBD devices, remote iSCSI targets, etc.).
The shared block device template will make the following assumptions:
To extend the shared block storage template and give Ganeti the ability to control and manipulate external storage (provisioning, removal, growing, etc.) we need a more generic approach. The generic method for supporting external shared storage in Ganeti will be to have an ExtStorage provider for each external shared storage hardware type. The ExtStorage provider will be a set of files (executable scripts and text files), contained inside a directory which will be named after the provider. This directory must be present across all nodes of a nodegroup (Ganeti doesn’t replicate it), in order for the provider to be usable by Ganeti for this nodegroup (valid). The external shared storage hardware should also be accessible by all nodes of this nodegroup too.
An “ExtStorage provider” will have to provide the following methods:
The proposed ExtStorage interface borrows heavily from the OS interface and follows a one-script-per-function approach. An ExtStorage provider is expected to provide the following scripts:
All scripts will be called with no arguments and get their input via environment variables. A common set of variables will be exported for all commands, and some of them might have extra ones.
All scripts except attach should return 0 on success and non-zero on error, accompanied by an appropriate error message on stderr. The attach script should return a string on stdout on success, which is the block device’s full path, after it has been successfully attached to the host node. On error it should return non-zero.
To support the ExtStorage interface, we will introduce a new disk template called ext. This template will implement the existing Ganeti disk interface in lib/bdev.py (create, remove, attach, assemble, shutdown, grow, setinfo), and will simultaneously pass control to the external scripts to actually handle the above actions. The ext disk template will act as a translation layer between the current Ganeti disk interface and the ExtStorage providers.
We will also introduce a new IDISK_PARAM called IDISK_PROVIDER = provider, which will be used at the command line to select the desired ExtStorage provider. This parameter will be valid only for template ext e.g.:
$ gnt-instance add -t ext --disk=0:size=2G,provider=sample_provider1
The Extstorage interface will support different disks to be created by different providers. e.g.:
$ gnt-instance add -t ext --disk=0:size=2G,provider=sample_provider1 \
--disk=1:size=1G,provider=sample_provider2 \
--disk=2:size=3G,provider=sample_provider1
Finally, the ExtStorage interface will support passing of parameters to the ExtStorage provider. This will also be done per disk, from the command line:
$ gnt-instance add -t ext --disk=0:size=1G,provider=sample_provider1,\
param1=value1,param2=value2
The above parameters will be exported to the ExtStorage provider’s scripts as the enviromental variables:
We will also introduce a new Ganeti client called gnt-storage which will be used to diagnose ExtStorage providers and show information about them, similarly to the way gnt-os diagose and gnt-os info handle OS definitions.
A new cluster configuration attribute will be introduced, named “storage_pools”, modeled as a dictionary mapping storage pools to external storage providers (see below), e.g.:
{
"nas1": "foostore",
"nas2": "foostore",
"cloud1": "barcloud",
}
Ganeti will not interpret the contents of this dictionary, although it will provide methods for manipulating them under some basic constraints (pool identifier uniqueness, driver existence). The manipulation of storage pools will be performed by implementing new options to the gnt-cluster command:
$ gnt-cluster modify --add-pool nas1 foostore
$ gnt-cluster modify --remove-pool nas1 # There must be no instances using
# the pool to remove it
Furthermore, the storage pools will be used to indicate the availability of storage pools to different node groups, thus specifying the instances’ “mobility domain”.
The pool, in which to put the new instance’s disk, will be defined at the command line during instance add. This will become possible by replacing the IDISK_PROVIDER parameter with a new one, called IDISK_POOL = pool. The cmdlib logic will then look at the cluster-level mapping dictionary to determine the ExtStorage provider for the given pool.
The gnt-storage client can be extended to support pool management (creation/modification/deletion of pools, connection/disconnection of pools to nodegroups, etc.). It can also be extended to diagnose and provide information for internal disk templates too, such as lvm and drbd.
Design for executing commands via RPC
Design for supporting custom SSH ports for nodes
Enter search terms or a module, class or function name.